All pull requests

Pull requests

• P2: work the way xTool Studio drives it; cameras, crop presets, overlays and laser moves

  #60·GizmoGoody opened Nov 9, 2026Contributor·

  ·

• Put the same entities in the same device page group on every model

  #59·GizmoGoody opened Nov 9, 2026Contributor·

  ·

• WS-V2: a push that arrives during the accessory read wins over the poll

  #58·GizmoGoody opened Nov 8, 2026Contributor·

  ·

• Auto power-off: turn the Power switch off after Idle or Sleeping

  #57·GizmoGoody opened Nov 8, 2026Contributor·

  ·

• Focus only with the surface lens on the F2 Ultra UV

  #56·GizmoGoody opened Nov 8, 2026Contributor·

  ·

• Access control: named as in Studio, only on the units Studio offers it on

  #55·GizmoGoody opened Nov 8, 2026Contributor·

  ·

• Never let camera photo requests pile up

  #54·GizmoGoody opened Nov 8, 2026Contributor·

  ·

• WS-V2: do not read the settings of a sleeping laser

  #53·GizmoGoody opened Nov 8, 2026Contributor·

  ·

• Show written values at once and hold them until the device reports them

  #52·GizmoGoody opened Nov 8, 2026Contributor·

  ·

• Find accessory devices through the config entry, not the deprecated registry mapping

  #51·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Add the Last job time sensor to the F2 Ultra UV

  #50·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Report a WS-V2 job the laser says failed as a failed job

  #49·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Add an IF2 2.0 Alert event for a fan stall and a cleaning reminder

  #48·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Assume the red dot is on after a V2 laser connects

  #47·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Add F2 Ultra UV Engraving lens, Wi-Fi signal and Calibration sensors

  #46·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Show Focusing, Warming up and Laser overheat in the F2 Ultra UV Status

  #45·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Document V2 endpoints that answer but do not work

  #44·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• F2 Ultra UV: main camera Calibration image

  #43·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Give each camera its own device; crop, xtool.camera and a deep camera Perspective select

  #42·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• F2 Ultra UV: straighten the main camera and turn the deep camera upright

  #41·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• F2 Ultra UV: Focus height, Autofocus and the xtool.focus action

  #40·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Task ID shows None when the laser has no job

  #39·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• WS-V2 camera: set how often each thumbnail refreshes

  #38·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• WS-V2 camera: faster photo live view, Idle when nobody watches

  #37·GizmoGoody opened Nov 7, 2026Contributor·

  ·

• Improve xTool Apparel Printer status reporting

  #36·corillis opened Nov 6, 2026·

  ·
  1