Issues

• Canned cycles are posted in the plane the last arc left (G81 under G18 drills along Y on LinuxCNC)

  bugposts
  stevecad/camlib#183 · Filter by author 10-X-eng opened on Nov 10, 2026 · Phase 1: Correctness

• LNC milling post (A-LNC milling series): reference post with independent decoder

  claimedenhancementposts
  stevecad/camlib#182 · Filter by author 10-X-eng opened on Nov 10, 2026 · Any time
  1

• Machine travel: one tip box per scene doesn't fit tools of different gauge lengths

  stevecad/camlib#176 · Filter by author 10-X-eng opened on Nov 10, 2026

• FANUC 0i-MB post with several tools needs measured tip positions

  stevecad/camlib#177 · Filter by author 10-X-eng opened on Nov 10, 2026

• Parallel: rows all cut one way

  stevecad/camlib#175 · Filter by author 10-X-eng opened on Nov 10, 2026

• Trace with a side offset (an open chain of edges, cutter on one side)

  stevecad/camlib#174 · Filter by author 10-X-eng opened on Nov 10, 2026

• Contour following the part's outline at each depth (silhouette)

  stevecad/camlib#173 · Filter by author 10-X-eng opened on Nov 10, 2026

• Tabs at given positions

  stevecad/camlib#172 · Filter by author 10-X-eng opened on Nov 10, 2026
  1

• Pocket and Contour: ramp entry along the path

  stevecad/camlib#171 · Filter by author 10-X-eng opened on Nov 10, 2026
  1

• Turning tools: one clearance angle for every side of the insert

  stevecad/camlib#170 · Filter by author 10-X-eng opened on Nov 10, 2026

• Arc radius check at zero tolerance depends on the platform's hypot

  stevecad/camlib#169 · Filter by author pzfreo opened on Nov 10, 2026

• Tool change: no mode for a controller whose M6 doesn't move (LinuxCNC T M6 G43 H)

  stevecad/camlib#168 · Filter by author 10-X-eng opened on Nov 10, 2026

• Roughing with AdaptiveClearing: no entry found, or the posted journal grows past 1 GB

  stevecad/camlib#167 · Filter by author 10-X-eng opened on Nov 10, 2026

• Machine travel: a move starting exactly on the travel limit is uncertain

  stevecad/camlib#166 · Filter by author 10-X-eng opened on Nov 10, 2026

• Roughing: the shank/holder guard can't prove clearance cleared by earlier layers unless a move exactly repeats one

  stevecad/camlib#160 · Filter by author pzfreo opened on Nov 9, 2026

• Milling: an operation that runs a caller-supplied toolpath through the same simulation, checks and posting

  stevecad/camlib#157 · Filter by author Wookie1 opened on Nov 9, 2026

• Optimize Geodesic finishing

  millingoptimization
  stevecad/camlib#118 · Filter by author 10-X-eng opened on Nov 7, 2026 · Phase 6: Optimization
  3

• Turning: solid (one-piece) boring bars with a ground head on a round bar

  enhancementturning
  stevecad/camlib#114 · Filter by author 10-X-eng opened on Nov 7, 2026 · Phase 3: Complete turning

• Turning: apply the insert's in-plane size tolerance (ISO 1832 d and m) to its body

  enhancementturning
  stevecad/camlib#113 · Filter by author 10-X-eng opened on Nov 7, 2026 · Phase 3: Complete turning

• Tool and holder bodies from supplied models (mesh in the engine; STEP via the CadQuery adapter)

  enhancementmillingturning
  stevecad/camlib#110 · Filter by author 10-X-eng opened on Nov 7, 2026 · Phase 3: Complete turning

• Haas NGC post: G86 needs a source for spindle restart

  postsquestion
  stevecad/camlib#97 · Filter by author 10-X-eng opened on Nov 7, 2026 · Any time

• Siemens 808D posts: tapping (CYCLE84 / G331, ISO G84/G74)

  enhancementposts
  stevecad/camlib#95 · Filter by author 10-X-eng opened on Nov 7, 2026 · Any time

• Optimize turning: face grooving (TurnFaceGroove)

  optimizationturning
  stevecad/camlib#57 · Filter by author 10-X-eng opened on Nov 6, 2026 · Phase 6: Optimization
  1

• Optimize turning: boring (TurnBoreRough, TurnBoreFinish)

  optimizationturning
  stevecad/camlib#56 · Filter by author 10-X-eng opened on Nov 6, 2026 · Phase 6: Optimization
  1

• Optimize turning: drilling on the axis (TurnDrill)

  optimizationturning
  stevecad/camlib#55 · Filter by author 10-X-eng opened on Nov 6, 2026 · Phase 6: Optimization
  1